PA200014 PA20/14
PA200015 PA20/15
PA20/15A
PA200016 PA20/16
PA200017 PA20/17
PA20/17A
PA20/17B
PA200018 PA20/18
PA200019 PA20/19
PA20/19A
PA200020 PA20/20
PA200021 PA20/21
Termination Panel. Rear termination panel for RC3/16 A.M.
receiver. Power requirements mains or d.c. PN3A/79. DD
1978. DDMI 5.360(78). DDHB 5.144(78).
Switch Termination Panel. Connects 14 wires from each of 3
ribbon cables to one 38 way Varicon fixed plug. For use
with SE2/3 Communications Switch Unit. PCB approximately
150mm x 150mm. SCPD 1978.
Termination Switch Panel. As PA20/15 but omitting
components not required when used in conjunction with a
capacitor microphone. SCPD 1978.
Termination Panel for Band 11 VHF drive bays. Drawer unit
483mm x 44mm with 9 x 12-way tag blocks. TCPD 1978.
Termination Panel. To interface a stereo coder type CD2/11
with external connections, i.e. mains, audio inputs, coded
output, control circuits etc. PN3A/54. DD 1978. DDMI
6.347(79). DDHB 6.173(79).
Termination Panel. To interface the Stereo Coder CD2/11
with external connections, i.e. mains, audio inputs, coded
output, control circuits etc. This 'A' version differs
from the standard version in that it also includes a TNC
output of 19 kHz and a TNC input of 57 kHz for injection of
Radio
Data.
Power
requirements
240
V
a.c.
Chassis
PN3A/54. Sub-units CD2/11. TCPD 1986.
Termination Panel. To interface a stereo coder type CD2/11
in Local Radio TIE with external connections Le. mains,
audio inputs, coded output etc. Also includes TNC output
of 19 kHz and TNC input of 57 kHz for injection of Radio
Data. Power requirements 240Vac. Chassis code: PN3A/54.
TCPD 1987.
Termination Panel. U Link termination panel for 15
circuits 2U high with designation strips and lacing bar.
BMM version of PA20/7. Supersedes PA20/7. SCPD 1978.
Termination Panel. The unit is intended for use with
receives RC1/12, RC1/12A, RC1/17, RC1/17A, RC1/15 and
RC3/15. It is used as a rear panel termination and
directly mountable to the rear of a 4U BMM nest box. Power
requirements d.c. or mains. PN3A/54A. Supersedes PA20/13.
DD 1979. DDMI 5.366(79).
Termination Panel. Rear termination panel for RC1/12,
RC1/12A, RC1/17 and RC3/15. Single 600Q load when receiver
is fed with 75kHz deviated RF signal. Power requirements
d.c. or mains. Supersedes PA20/13D. ED 1980.
Termination Panel. The unit is intended for use with
receivers RC1/12, RC1/12A, RC1/17, RC1/17A, RC1/15 and
RC3/15. It is used as a rear panel termination and
directly mountable to the rear of a 4U BMM nest box.
Single A.F. outputs at low impedance are available without
multiplex. Power requirements d.c. or mains. PN3A/54A.
Supersedes PA20/13. DD 1979. DDMI 5.368(79).
Termination Panel for DM4/2.
1980.
PN3A/50A and PN3A/54A.
DD
215

15