and 1 Power Supplier PS3/71. Power requirements 240 Vac.
3 U main frame. DD 1985. DDMI 3.752(85).
PN030075 PN3A/75A-H,J Dummy Panel. 2U panels to fit the 483mm frame PN3/55 and
to blank off any empty space. Eight widths A to H together
with the narrow 'J' size. DD 1976. DDMI 1.230(79). DDMI
3.752(85).
PN3/75
General
Purpose
Panel.
Panel
to
mount
10
amplifiers
AM7/25. Power requirements t24 V. 3U Main Frame. DD
1984. DDMI 3.752(85).
PN030076 PN3A/76A-H,J Dummy Panel. 3U panel to fit the 483mm frame PN3/58 and to
blank off any empty space. Eight widths A to H together
with the narrow 'J' size. DD 1976. DDMI 1.236(79).
PN3/76
Auto-Phase Panel.
Panel
to
accommodate
one
PS3/64,
one
UN26/601, and up to eleven AM1/614s or AM4/536s with
corresponding termination panels, in any combination.
PN3/54. DD (8) 1985.
PN030077 PN3/77
Control Panel Chassis.
This chassis holds the two Control
Panels (PA6/170 & PA6/171) for the EP5M/529 Digital Vision
Mixer.
It
consists
of
BMM
component
parts,
so
that
the
panels themselves mount like standard BMM chassis. D&ED
(V) 1987.
PN030078 PN3A/78
G.P.
Termination Panel.
This panel consists of a simple
bracket with four captive screws. It fits a 2U frame and
can only be used with either the PN3A/51A or a P.O. mother
board. It is 'A' size (53mm wide) and is punched for a
mains connector. DD 1977. DDMI 1.237(79).
PN030079 PN3A/79
G.P. Termination Panel.
This panel consists of a simple
bracket with four captive screws. It fits a 4U frame and
can only be used with either the PN3A/50A or a P.C. mother
board. It is 'A' size (53mm wide) and is punched for a
mains connector. DD 1977. DDMI 1.226(78).
PN030080 PN3A/80
Termination Panel or cover to fit a 2U frame (PN3/56).
It
consists of a full width cover supported on pillars from
the main termination panel and a lacing bar. Used mostly
on shallow bays, where the panel is to be 'hard wired' to
the bay. DD 1977. DDMI 1.244(79).
PN030081 PN3A/81
Panel to fit the 2U frame PN3/55 and cover up unsupported
P.C. boards. It is retained by a clip on its lower edge
and a thumbscrew on its top edge. Usual 8 widths
designated A-H, supersedes the hinged cover PN3A/7 2. DD
1977. DDMI 1.228(79).
PN030082 PN3A/82
Panel to fit the 3U frame PN3/58 and cover up unsupported
P.C. boards. It is retained by a clip on its lower edge
and a thumbscrew on its top edge. Usual 8 widths
designated A-H, supersedes the hinged cover PN3A/6 8. DD
1977. DDMI 1.229(79).
PN030083 PN3A/83
Panel to fit the 4U frame PN3/54 and cover up unsupported
P.C. boards. It is retained by a clip on its lower edge
and a thumbscrew on its top edge. Usual 8 widths
225

25